TSOP12.. IR Receiver Modules for Remote Control

Transkript

Not for New Design
TSOP12..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Very low supply current
• Photo detector and preamplifier in one
package
• Internal filter for PCM frequency
• Improved shielding against EMI
• Supply voltage: 2.5 V to 5.5 V
• Improved immunity against ambient light
1
• Insensitive to supply voltage ripple and noise
• Compliant to RoHS Directive 2011/65/EU and in
accordance to WEEE 2002/96/EC
2
94 8691
3
Note
** Please see document “Vishay Material Category Policy”:
www.vishay.com/doc?99902
MECHANICAL DATA
DESCRIPTION
Pinning:
The TSOP12.. series are miniaturized receivers for infrared
remote control systems. A PIN diode and a preamplifier are
assembled on a lead frame, the epoxy package acts as an
IR filter.
The demodulated output signal can be directly decoded by
a microprocessor. The TSOP12.. is compatible with all
common IR remote control data formats.
This component has not been qualified according to
automotive specifications.
1 = GND, 2 = VS, 3 = OUT
PARTS TABLE
CARRIER FREQUENCY
STANDARD APPLICATION (AGC2/AGC8)
30 kHz
TSOP1230
33 kHz
TSOP1233
36 kHz
TSOP1236
36.7 kHz
TSOP1237
38 kHz
TSOP1238
40 kHz
TSOP1240
56 kHz
TSOP1256
BLOCK DIAGRAM
APPLICATION CIRCUIT
16832
17170_5
2
VS
3
Input
AGC
Band
pass
Demodulator
R1
IR receiver
VS
Circuit
30 kΩ
Transmitter
with
TSALxxxx
OUT
+ VS
C1
µC
OUT
GND
VO
GND
1
PIN
Rev. 2.5, 21-Feb-12
Control circuit
R1 and C1 are recommended for protection against EOS.
Components should be in the range of 33 Ω < R1 < 1 kΩ,
C1 > 0.1 µF.
GND
1
Document Number: 82013
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP12..
www.vishay.com
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
VALUE
Supply voltage (pin 2)
TEST CONDITION
VS
- 0.3 to + 6
UNIT
V
Supply current (pin 2)
IS
3
mA
Output voltage (pin 3)
VO
- 0.3 to (VS + 0.3)
V
Output current (pin 3)
IO
5
mA
Tj
100
°C
Storage temperature range
Tstg
- 25 to + 85
°C
Operating temperature range
Tamb
- 25 to + 85
°C
Tamb  85 °C
Ptot
10
mW
t  10 s, 1 mm from case
Tsd
260
°C
Junction temperature
Power consumption
Soldering temperature
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
VS
2.5
Ev = 0, VS = 3.3 V
ISD
0.27
Supply voltage
Supply current (pin 2)
TYP.
MAX.
0.35
UNIT
5.5
V
0.45
mA
Ev = 40 klx, sunlight
ISH
0.45
mA
Ev = 0, test signal see fig. 1,
IR diode TSAL6200,
IF = 250 mA
d
45
m
IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see fig. 1
VOSL
Minimum irradiance
Pulse width tolerance:
tpi - 5/f0 < tpo < tpi + 6/f0,
Ee min.
Maximum irradiance
tpi - 5/f0 < tpo < tpi + 6/f0,
Ee max.
Directivity
Angle of half transmission
distance
1/2
Transmission distance
Output voltage low (pin 3)
0.15
100
mV
0.35
mW/m2
W/m2
30
± 45
deg
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Optical Test Signal
1.0
(IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms)
0.9
tpo - Output Pulse Width (ms)
Ee
t
tpi *
* tpi
VO
T
10/f0 is recommended for optimal function
Output Signal
1)
2)
VOH
16110
7/f0 < td < 15/f0
tpi - 5/f0 < tpo < tpi + 6/f 0
Output Pulse Width
0.8
Input Burst Length
0.7
0.6
0.5
0.4
0.3
λ = 950 nm,
Optical Test Signal, Fig.1
0.2
0.1
0
VOL
td 1)
tpo 2)
0.1
t
20752
Fig. 1 - Output Active Low
Rev. 2.5, 21-Feb-12
1
10
102
103
104
105
Ee - Irradiance (mW/m2)
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
2
Not for New Design
TSOP12..
www.vishay.com
600 µs
t
600 µs
t = 60 ms
94 8134
Output Signal, (see fig. 4)
VO
VOH
VOL
t on
4
Ee min. - Threshold Irradiance (mW/m2)
Optical Test Signal
Ee
Correlation with Ambient Light Sources:
2
3.5 10 W/m = 1.4 kLx (Std. illum. A, T = 2855 K)
10 W/m2 = 8.2 kLx (Daylight, T = 5900 K)
3
2
1.5
1
0.5
0
0.01
t
t off
Wavelength of Ambient
Illumination: λ = 950 nm
2.5
20757
Ton
0.6
0.5
Toff
0.4
0.3
0.2
λ = 950 nm,
Optical Test Signal, Fig. 3
0
0.1
1
20759
10
Ee - Irradiance
100
1000
100
f = 100 Hz
0.9
0.8
f = 10 kHz
0.7
0.6
f = 20 kHz
0.5
0.4
f = 30 kHz
0.3
f = fo
0.2
0.1
0
10 000
1
(mW/m2)
10
100
1000
VsRMS - AC Voltage on DC Supply Voltage (mV)
20753
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
Fig. 4 - Output Pulse Diagram
500
E - Max. Field Strength (V/m)
1.2
1.0
E e min./Ee - Rel. Responsivity
10
1.0
Ton, Toff - Output Pulse Width (ms)
0.8
0.1
1
Fig. 6 - Sensitivity in Bright Ambient
Fig. 3 - Output Function
0.7
0.1
Ee - Ambient DC Irradiance (W/m2)
0.8
0.6
0.4
f = f0 ± 5 %
Δ f(3 dB) = f0/10
0.2
450
400
350
300
250
200
150
100
50
0
0.0
0.7
16925
0.9
1.1
0
1.3
20747
f/f0 - Relative Frequency
1000
1500
2000
2500
3000
f - EMI Frequency (MHz)
Fig. 8 - Sensitivity vs. Electric Field Disturbances
Fig. 5 - Frequency Dependence of Responsivity
Rev. 2.5, 21-Feb-12
500
3
Not for New Design
TSOP12..
www.vishay.com
0°
1
10 °
20 °
30 °
Max. Envelope Duty Cycle
0.9
0.8
0.7
40 °
0.6
1.0
0.5
0.4
TSOP12..
0.3
0.2
0.9
50 °
0.8
60 °
70 °
0.7
80 °
0.1
f = 38 kHz, Ee = 2 mW/m²
0
0
20773-1
20
40
60
80
100
120
0.6
Burst Length (number of cycles/burst)
0.2
0
0.2
0.6
0.4
Fig. 12 - Horizontal Directivity
Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length
0°
0.3
10 °
20 °
30 °
0.25
40 °
0.2
1.0
0.9
50 °
0.1
0.8
60 °
0.05
0.7
0.15
70 °
80 °
0
- 30
- 10
10
30
50
70
90
0.6
Tamb - Ambient Temperature (°C)
20755
95 11339p2
0.4
0.2
0
0.2
0.6
0.4
d rel - Relative Transmission Distance
Fig. 13 - Vertical Directivity
Fig. 10 - Sensitivity vs. Ambient Temperature
1.2
0.2
Ee min. - Sensitivity (mW/m2)
S (λ)rel - Relative Spectral Sensitivity
0.4
d rel - Relative Transmission Distance
95 11340p2
1.0
0.8
0.6
0.4
0.2
0.18
0.16
0.14
0.12
0.1
0.08
0.06
0.04
0.02
0
750
94 8408
0
850
950
1050
2
1150
λ - Wavelength (nm)
20756
3
3.5
4
4.5
5
5.5
6
VS - Supply Voltage (V)
Fig. 14 - Sensitivity vs. Supply Voltage
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
Rev. 2.5, 21-Feb-12
2.5
4
Not for New Design
TSOP12..
www.vishay.com
SUITABLE DATA FORMAT
IR Signal
The TSOP12.. series is designed to suppress spurious
output pulses due to noise or disturbance signals. Data and
disturbance signals can be distinguished by the devices
according to carrier frequency, burst length and envelope
duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the TSOP12.. in the
presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance
signals which are suppressed are:
• DC light (e.g. from tungsten bulb or sunlight)
0
• Continuous signals at any frequency
10
5
15
20
Time (ms)
16920
Fig. 15 - IR Signal from Fluorescent Lamp
with Low Modulation
IR Signal
• Strongly or weakly modulated noise from fluorescent
lamps with electronic ballasts (see figure 15 or figure 16)
0
16921
5
10
15
20
Time (ms)
Fig. 16 - IR Signal from Fluorescent Lamp
with High Modulation
TSOP12..
Minimum burst length
10 cycles/burst
After each burst of length
a minimum gap time is required of
10 to 70 cycles
 10 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
70 cycles
> 4 x burst length
Maximum number of continuous short bursts/second
1800
Recommended for NEC code
yes
Recommended for RC5/RC6 code
yes
Recommended for Sony code
yes
Recommended for Thomson 56 kHz code
yes
Recommended for Mitsubisi code (38 kHz, preburst 8 ms, 16 bit)
yes
Recommended for Sharp code
yes
Suppression of interference from fluorescent lamps
Most common disturbance signals are suppressed
Note
• For data formats with short bursts please see the datasheet for TSOP11.., TSOP13.
Rev. 2.5, 21-Feb-12
5
Not for New Design
TSOP12..
www.vishay.com
PACKAGE DIMENSIONS in millimeters
10
± 0.3
(9.2)
0.65
+ 0.10
- 0.15
0.8 max.
30.6
± 0.5
12.5
± 0.4
Center of sensitive area
0.5
Area not plane
0.4
+ 0.15
- 0.05
2.54 nom.
+ 0.10
- 0.05
1.4 ± 0.3
3 x 2.54 = 7.62 nom.
4 ± 0.3
5.8
± 0.3
R 2.75
technical drawings
according to DIN
specifications
Drawing-No.: 6.550-5095.01-4
Issue: 20; 15.03.10
96 12116
Rev. 2.5, 21-Feb-12
6
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1

TSOP12.. IR Receiver Modules for Remote Control

Transkript

Benzer belgeler

ftc750 750 w fm transmitter

Sonar Beacon System - Ana Sayfa

University Of Arkansas For Medical

Atmospheric Effects in SAR Interferometry

PDF ( 2 )